I want to refinish the deck of my 31' and remove the stanchions to rechrome.  In the Super Disk (yup, I checked there first), I found a reference that the stanchions on a 41 were backed by a plate that is tapped for the thru bolts and the plates are screwed to the bottom of the deck so they will not fall in the bilge.  Is this true for my 1968 31" as well? If that is true, makes the job almost easy for a change.

Eppa Hunton

At Last

Views: 425

Reply to This

Replies to This Discussion

The 31 stanchions are bolted in with nuts and washers. With a little effort you can access them.

Eppa,  If you will go into your engine room and go to the easiest side you will see them!  I don't remember about the 31 but I do know finding them is easy from the inside.  Lee Dahlen, Glassic Boatworks  Facebook: www.facebook.com/Glassicboatworks

Hey guys, how about the 42?  When I replaced the life line I tighten some of the screws and had a few spinners.

 

Byron

EPPA-I am finally back in action 3 level spinal fusion and i am much better old 37 Connie is back in slip after extensive woodwork,Call me and I wiill meet you down at the dock neighbor and assist in any way I am able.Still not 100% but slowly getting there.Filled cylinders on 31 Commander over summer crank will hardly budge,but have a friend who has a 4 wheel drive crane that will remove engines for me to over haul.Do call me at your leisure please

Glad to hear you have had success getting the Connie back in the water.  Heard from Costa, that shafts props and more got treatment as well.

I was aware that the stantions around the transome had four bolts with nuts and washers.  Was hoping that the method on the 42 with a plate screwed to the underside and tapped for the screws which would ease the process.  No such luck.  Then the comment about removal of side walls confirms this is not a project for the neophyte.  Besides I have new walpaper installed!

David contact me off list about a suggestion for your siesed  motors.

Eppa 

eppa2h@comcast.net

David Rhodes,II said:

EPPA-I am finally back in action 3 level spinal fusion and i am much better old 37 Connie is back in slip after extensive woodwork,Call me and I wiill meet you down at the dock neighbor and assist in any way I am able.Still not 100% but slowly getting there.Filled cylinders on 31 Commander over summer crank will hardly budge,but have a friend who has a 4 wheel drive crane that will remove engines for me to over haul.Do call me at your leisure please

Reply to Discussion

RSS

Club News

2019 Wall Calendars Now Available!!

The Chris-Craft Commander Club 2019 Wall Calendar is now available!!.  We're having to do things a little differently this year, so for calendar details & ordering, Click Here

_________________________________________

2018 Photo Contest Winner

The 4th Annual Chris-Craft Commander Club Photo Contest had more than 50 entries and selecting the winners was not an easy task. 

First place: submitted by Pat Chaps

Second place: submitted by Martin Krall;

Third place: submitted by Jeff Pacy.

To view all entries to this year's contest,         Click Here

________________________________________

The 2018 Chris-Craft Commander Club National Rendezvous is in the books and it was a great time!!

City of Mentor, Ohio

The city of Mentor, Ohio and the Lawnfield Inn & Suites were wonderful hosts.  A special Thanks to Rob Kneen, the local member sponsor, and Char Pike for the hours of hard work put in organizing and coordinating an amazing weekend. 

The Rendezvous Photo Albums can be accessed through the links below, as well as, under Library, Photo Albums.  We will continue to add links to other albums as they become available. Also below, you will find links to a couple articles written for the local newspaper.

Photo Album 1                 Photo Album 2  

Photo Album 3

Articles:

Chris-Craft Commander Club Celebrates Anniversary in Mentor

Chris-Craft Commander connoisseurs congregate at Mentor Lagoons Marina

_________________________________________

 

© 2018   Created by CCCC Webmaster.   Powered by

Badges  |  Report an Issue  |  Terms of Service