I have '73 Sport Sedan and need to replace the packing in the drive shafts.  How do I determine the size packing that I need?  Do I just measure the drive shafts or are there other measurements?

Views: 118

Reply to This

Replies to This Discussion

I bought all 3 sizes at West Marine and took back the ones that didn’t fit. My ‘66 31 uses 1/8th” packing, I’m told that’s unusual, but it is what it is. 

Measure the diameter of the shaft, measure the ID of the gland which is the OD  shaft gland. the difference is the packing size.  ie.  1 3/8" shaft 1 3/4" gland on the shaft =3/8 packing

My guess would be that your packing is 1/4 I inch  and don't tighten the packing nut to much you want it to drip small amount when running in gear

Thanks.  I measured the shaft to be 1 1/4 and the gland OD 1 7/8.  So doing the math I get an odd size of .62. Does that seem right would it round to 1/2" packing?  Also, and idea of packing material type to use there are a lot to choose from.  Finally, do you know how many strands to pack would it be three?

Timothy "Tim" Miller said:

Measure the diameter of the shaft, measure the ID of the gland which is the OD  shaft gland. the difference is the packing size.  ie.  1 3/8" shaft 1 3/4" gland on the shaft =3/8 packing

ID of gland is probably 1 3/4" so 1/4" packing gives the 1/2" difference  for circumference of shaft +packing.  Sorry about the poor previous explanation.

Tim

I do not know if you if you got the size figured out yet but use graphite packing.The old bees wax and teflon packing are out dated.The bees wax melts and the teflon wears out the shaft.The graphite lubricates and blocks the water molecules from passing thru.It takes very little tightening to stop the flow of water. And because it lubricates and cools you do not I repeat you do not need to have them drip.I hope this helps. Don

1/4"

Reply to Discussion

RSS

Club News

2019 Regional Rendezvous Hosts Wanted

Are you yearning for a little fix for Commander-itis?

Would you like to meet other Commander owners in your area?

Do you have a great idea for a Commander gathering on or off the water?

If you answered yes to any of these questions, then we have just the remedy for you: We encourage you to think about hosting, or, indicating your interest in hosting a Regional Rendezvous in your area in 2019.

For more information about hosting - click here:

Hosting A Rendezvous

Char Pike has volunteered to be the EC “Point Person” for 2019 Regional Rendezvous. Please contact Char if you are interested in organizing & holding a Regional Rendezvous in your area. Char’s e-mail address is rendezvous.commanderclub@gmail.com

_________________________

Help Wanted!!!

New Faces, New Perspectives - Executive Committee Openings to start in January 2020

Would you like to be more active in the Commander Club? Would you like to help chart our course? Are you willing to commit the time, energy and creativity needed to assist us in promoting and supporting our mission?

We are searching for new faces and new perspectives. Positions start in January 2020 for a two year term.

There are four positions available. Chief Commander, Treasurer, Public Relations Chair and Membership Chair.

Duties for each position are located in the bylaws https://commanderclub.com/page/bylaws

More details about each position here.

The Executive Committee (EC) convenes monthly via conference call. Meetings typically last 90 minutes or less. Most work done via e-mail. Each job has its own time commitment depending on club activities. Current EC members will mentor you.

Interested in any of these positions?

Please drop Char Pike an e-mail at archivist.commanderclub@gmail.com

________________

2018 Photo Contest Winner

The 4th Annual Chris-Craft Commander Club Photo Contest had more than 50 entries and selecting the winners was not an easy task. 

First place: submitted by Pat Chaps

Second place: submitted by Martin Krall;

Third place: submitted by Jeff Pacy.

To view all entries to this year's contest,         Click Here

© 2019   Created by CCCC Webmaster.   Powered by

Badges  |  Report an Issue  |  Terms of Service